Monthly Archives: July 2021

News

Advantages of Power Transmission Belts

There are various types of power transmission devices commonly used in industry today. Among them for example, chains, gears, v-belts and synchronous belts are widely used. The focus of this exercise will be a general introduction to rubber power transmission belts and more specifically, those v-belts and synchronous belts used in the Heating, Ventilation, Air Conditioning and Refrigeration (HVAC-R) industry.

  • Lowest cost means of transmitting power
  • Ability to accommodate a wide range of speeds and center distance between driver and driven shaft
  • Quiet and clean operation
  • Require no lubrication like chains, gears and gearboxes
  • Able to absorb shock loads and pulsations
  • Can be used for special applications such as clutching and variable speed
News

Why choose a V belt?

These are the most commonly used V belts for power transmission. At the same level of tension, they transmit higher power than flat belts. They are used, for example, in variable-speed drives. They offer the best combinations of traction, speed, bearing load and service life.

Advantages:

  • The V-shaped section of the belt follows a groove in the pulley, which prevents the belt from slipping and improves torque transmission.
  • It is less wide than a flat belt and therefore takes up less space.
  • It doesn’t need to be as taut.
  • The optimal speed range is between 300 and 2,130 m/min.
  • For high power requirements, two or more V belts can be assembled side by side in an arrangement called a “multiple belt drive.”

V belts, also called trapezoidal belts, can be made of rubber or polymer without reinforcement, or they can have fibers incorporated into the rubber or polymer to increase strength. These fibres can be made of textile material (such as cotton), polyamide (such as nylon), polyester or, for greater strength, steel or aramid (such as Kevlar).

When a seamless belt does not meet the requirements of the application, articulated V belts can be used. Most models offer the same power and speed as endless belts of the same size and do not require special pulleys to operate. They are easy to install and have a higher environmental resistance than rubber belts. They are also adjustable in length if you choose to remove the links.

This article comes from directindustry edit released

News

Transmission Belt Pulleys For All Applications

Transmission belt pulley and round belt pulley solutions are designed to be the perfect solution for low and fractional horsepower drives. High quality and ruggedly engineered, these pulleys are ideal for application where high strength to weight ratios and quiet operation are required.

Like all transmission belt pulleys, the transmission belt pulleys utilize the advantages of nylon construction while also using a machined aluminum hub for additional strength. The nylon construction keeps the pulleys lightweight so they have lower inertia, and therefore lower energy requirements. This means that a smaller motor may be used, the time to accelerate and decelerate is decreased, and the machines overall process time is greatly increased.

Contact us to learn about our transmission belt pulley and round belt pulley solutions or to inquire about non-standard sizes and designs.

This article comes from torquetrans edit released

News

What are the two types of accessory drive belts?

There are two types of accessory drive belts, V-type and serpentine. Which one you have depends on your specific vehicle. Since the mid-1990s, most cars and trucks use serpentine belts, though you may find a few stragglers into the early 2000s. The accessory drive belts are what connect the accessories to the crankshaft.

Likewise, what are the two types of drive belts?

The most common types of drive belts in car’s engine are:

  • Serpentine belts
  • Advantages of Serpentine belts
  • Symptoms and causes of failing Serpentine belts
  • Timing belts
  • Advantage of Timing belts
  • V-Belt of cars
  • Symptoms and causes of failing V-Belts

Also, what does the accessory drive belt do? An accessory drive belt is a belt that drives all of the accessories that are in the engine of your vehicle. These accessories include the alternator, the water pump, the air conditioner compressor, and the power steering pump.

Subsequently, one may also ask, what are the different types of belts used in an engine?

There are different types of car belts, and their job is to keep the engine running by transferring power to various parts.

Here’s a brief discussion of the standard belts in a car and how they work.

  • Timing Belts. Car engine with timing belt.
  • V-belts. V-belt.
  • Serpentine Belts. A serpentine belt.

What kind of belts are there?

Different types of belts

  • Buckle belt
  • Horseshoe buckle belt
  • Suspender belt
  • Cummerbund
  • Military belt
  • Metal belts
  • Hip belt
  • Yoke belt

This article comes from askinglot edit released

News

Wedge V Belts

Effectively handling drives up to 750kW, these belts rank high in kWh per cost, the ultimate measure of drive value. The narrow belt cross section SPZ, SPA, SPB, SPC and 3V, 5V, 8V offerhigher power capacity for any sheave size and weight.

The narrow or wedge design provides more tensile member support than classical V belts. Narrow belts handle an equivalent load, but with narrower face width and smaller diameters than the traditional V belts. These features allow the use of smaller belts or fewer belts to transmit the load, an important advantage if your goal is to maximize power transmission effciency by reducing drive weight and size.

This article comes from vbeltsupply edit released

News

According to Material used for transmission belt

Leave a comment

The material used for transmission belts and ropes must be strong and flexible and should have high coefficient of friction to provide higher efficiency. So the transmission belts material plays a major role in power transmission. According the transmission belt material is classified as follow.
1. Leather belt:

This are the most important transmission belt used in workshops. It is made by 1.2 meter to 1.5 meters long strips cut from either side of the bhack bone of the top grade steer hides. The hair side of lather is more smoother and harder than the flesh side but the flesh side is interwoven and parallel to the surface. The leather may be either oak-tanned or mineral salt tanned. To increase the thickness of transmission belts, the strips are cemented together. According to this the transmission belt are designate by the numbers of layers, single ply, double ply etc.
2. Cotton or fabric belt:

Canvass or cotton duck are used in the fabric transmission belts. These transmission belts are made by three or more layer stitching together. These transmission belts are woven also into a strip of the desired width and thickness. These transmission belts are impregnated with some filler like linseed oil in order to make transmission belts water proof and to prevent injury to the fibers. The cotton transmission belts are suitable in warm climates, in damp atmospheres and in exposed positions. Since cotton transmission belts require little attention, therefore these transmission belts are used in farm machinery, transmission belt conveyor etc.
3. Rubber belt:

The rubber belts are made of layers of fabric impregnated with rubber composition and have a thin layer of rubber on the faces. These transmission belts are very flexible but the quickly destroyed if allowed to come into contact with heat, oil and grease. The rubber has elastic quality so these transmission belts are easily made endless. These transmission belts are found suitable for saw mills, paper mills where they are exposed to moisture.
4. Balata belts:

These transmission belts are similar to rubber belts except that balata gum is used in place of rubber. These transmission belts are acid proof and water proof and it is not effected by animal oils or alkalies. This transmission belt has higher strength than rubber belt.

These are the main types of transmission belts used in industries and material used to manufacture transmission belts. If you got any query, put in comment box. If you like this article, don’t forget to share it on social networks. Subscribe our website for more informative articles. Thanks for reading it.

News

Types And Material Of Drive Belt

Leave a comment

A drive belt, in machinery, a pair of pulleys attached to usually parallel shafts and connected by an encircling flexible belt (band) that can serve to transmit and modify rotary motion from one shaft to the other.

Belts are looped over pulleys and may have a twist between the pulleys, and the shafts need not be parallel. Most drive belts consist of flat leather, rubber, or fabric belts running on cylindrical pulleys or of belts with a V-shaped cross-section running on grooved pulleys.

There are Seven different types of drive belt can be found and those are:

1. Open Drive Belt

The open drive belt is used with shafts arranged parallel and rotating in the same direction. In that case, the driver pulls the belt from one side and delivers it to the other side.

Thus, the tension in the lower side belt will be higher than the upper side belt. The lower side belt is known as the tight side belt while the upper side belt is known as the slack side belt.

2. Closed Or Crossed Drive Belt

Cross or twisted drive belts are used with rotating shafts in parallel and opposite directions. In this case, the driver pulls the belt from one side and delivers it to the other side.

3. Fast And Loose Cone Pulley

This type of drive belts is used when the driven or machine shaft is to be started or stopped whenever desired without interfering with the driving shaft. A pulley which is keyed to the machine shaft is called a fast pulley and run at the same speed as that of the machine shaft.

A loose pulley runs freely over the machine shaft and is incapable of transmitting any power. When the driven shaft is required to be stopped, the belt is pushed on to the loose pulley by means of a sliding bar having belt forks.

4. Stepped Cone Pulley Drive

A step or cone pulley drive is used to change the speed of the driven shaft, while the main or driving shaft moves at a constant speed. This is accomplished by shifting the belt from one part of the steps to another.

A step cone pulley is an integral casting consisting of three or different numbers of different sizes of pulleys adjacent to each other, as shown in fig. A set of driven cone pulleys is placed upside down on the drive shaft. An endless belt will be wrapped around a pair of pulleys.

5. Jockey Pulley Drive.

In an open drive belt arrangement, if the center distance is small, or if the driven pulley is too small, the arc of the belt’s contact with the driven pulley will be very small, which reduces the tension in the belt, or if the belt requires Stress cannot be achieved by other methods, a sluggish pulley, called a jockey pulley, is placed on the slack side of the belt as shown in fig.

6. Quarter Turn Drive Belt

Quarter turn drive belts are also known as right-angle drive belts. It is used with shafts arranged at right angles and rotating in a certain direction. To prevent the belt from leaving the pulley, the width of the face of the pulley must be greater than or equal to 1.4 b, where b is the width of the belt. If the pulley cannot be arranged or when reversible speed is desired, a quarter-turn drive belt with a guide pulley may be used.

7. Compound Drive Belt

A compound drive belt is used when power is passed from one shaft to another through multiple shafts.

This article comes from engineering edit released